0,00
PRODUCT SPARE PARTS
-COMPOSITE LADDER - 4 PCS
-STAIR RAILING – 4 PCS
-116X116 COMPOSITE SQUARE PLATFORM - 7 PCS
-116X116 COMPOSITE TRIANGULAR PLATFORM - 12 PCS
-H:100 cm TOWER PIPE – 20 PCS
-H:150 cm TOWER PIPE – 6 PCS
-POLYETHYLENE KING ROOF – 4 PCS
-POLYETHYLENE HEXAGONAL ROOF – 1 PCS
-H:100 cm POLYETHYLENE RIGHT INCLINED SLIDE – 1 PCS
-H:100 cm POLYETHYLENE LEFT INCLINED SLIDE – 1
-H: 150 cm POLYETHYLENE SPIRAL TUNNEL – 1 PCS
-H: 100 cm POLYETHYLENE FLAT SLIDE – 1 PCS
-H: 100 cm POLYETHYLENE SPIRAL SLIDE – 2 PCS
-H: 100 cm POLYETHYLENE DOUBLE FLAT SLIDE – 1 PCS
-H: 100 cm POLYETHYLENE TUBE SLIDE – 1 PCS
-H: 150 cm POLYETHYLENE SPIRAL SLIDE – 1 PCS
-POLYETHYLENE TUBE PASSAGE – 2 PCS
-POLYETHYLENE POULTRY ROOF – 1 PCS
-POLYETHYLENE LANDING BARRIER – 22 PCS
-POLYETHYLENE CLIMBING BLOCK – 1 PCS
-POLYETHYLENE SHIP NOSE KIT – 2 PCS
-POLYETHYLENE CLIMBING ELEMENT – 1 PCS
-H: 100 cm SPRING BRIDGE CROSSING – 3 PCS
-POLYETHYLENE SPRING BRIDGE CROSSING RAILING – 3 PCS
-POLYETHYLENE FLOWER FIGURE – 3 PCS
-H: 100 cm CLIMBING UNIT – 1 PCS
POLYETHYLENE PRODUCTS
Low or common density linear polyethylene (LLDPE) is a thermoplastic used in various products.
It is a semi-permeable, softenable and highly durable polymer, and is a highly preferred product in the industry due to its low cost and high resistance. Polyethylene is classified into various categories based on its density and chemical properties.
Its mechanical properties depend on its molecular weight, crystal structure and branching type. Although its properties vary according to the types; good resistance to external environment conditions and moisture, flexibility, weak mechanical strength and superior chemical resistance can be counted as general properties. Polyethylene products are used in the production of slides, stairs, railings, barriers, accessories, roofs etc.
In order to prevent color fading in polyethylene products, the ''Light Fastness'' test value of masterbatch dyes used to color polyethylene products should be 6 or above.
Product thickness should be minimum 6 mm at points exposed to pressure and friction, and minimum 4 mm in barrier and shade products that are not exposed to any pressure. The material should be distributed evenly and create equal thickness. The wall thickness of the products and the deviation tolerance of the dimensions are 5%.
BEARING CONSTRUCTION
Minimum 114 mm. diameter, minimum 2 mm wall thickness TS EN 10219-2, TS-6476,It will be manufactured in accordance with DIN 2394 standards, cold formed and welded with high frequency welding, within the tolerance, size and section size range specified in the standard; It will consist of circular section steel pipes. This carrier construction will consist of pipes painted by baking with polyester based electrostatic powder oven paint over sandblasting.
ELECTROSTATIC POWDER OVEN PAINT
In order to remove oil, dirt and rust that will prevent painting on all metal parts, the pores on the material will be opened with the sandblasting method, which is the most effective method, and it will be made ready for painting in order to hold the paint better. ,
It will be done by spraying the fine ball material filled into a pressure-resistant cabin with pressurized air to open the pores where the paint will hold and to remove the oil, rust and dirt on the metal material.
After all the metal parts are manufactured, they will be coated with polyester-based electrostatic paint and baked in an oven at 200-220 degrees for 20 minutes to complete the painting process.
After all the metal parts are manufactured, they will first be rinsed in a 5% concentration degreasing bath at 70 degrees for 10 minutes and then immersed in a 1% concentration iron bath at 50 degrees for 15 minutes.
Then, rinsing and drying processes will be carried out again, the material will be coated with durable polyester-based powder paint for electrostatic system exteriors and baked in ovens at 180-200 degrees for 20-30 minutes to complete the painting process. The entire product will be painted as a single piece after welding to prevent the welded areas from rusting.After rinsing in a 5% concentration degreasing bath at 70 degrees for 10 minutes, it will be immersed in a 1% concentration iron bath at 50 degrees for 15 minutes.
Then, rinsing and drying processes will be carried out again, the material will be coated with durable polyester-based powder paint for electrostatic system exteriors and the painting process will be completed by baking in ovens at 180-200 degrees for 20-30 minutes. The entire product will be painted as a single piece after welding to prevent rust on the welded areas.After rinsing in a 5% concentration degreasing bath at 70 degrees for 10 minutes, it will be immersed in a 1% concentration iron bath at 50 degrees for 15 minutes.
Then, rinsing and drying processes will be carried out again, the material will be coated with durable polyester-based powder paint for electrostatic system exteriors and the painting process will be completed by baking in ovens at 180-200 degrees for 20-30 minutes. The entire product will be painted as a single piece after welding to prevent rust on the welded areas.